Sunday, June 12, 2011

Groggy's Workbench


In August 2008, hobbiest woodworker Groggy, started working on a humble roubo workbench in Melbourne. Over the past 2 years his documented the build in detail over at the Woodwork Forums. The Bench is 2520 x 650 x 140mm and made from solid Jarrah. He estimates the bench weights in at 200kg. It has a Bench Crafted wagon vice and a sliding deadmen. A unique feature of his bench is under the flush shelf is a purpose built parallel clamp rack. Very handy. There's a still a few things to finish off, but it's already a fantastic bench.

Picasa SlideshowPicasa Web AlbumsFullscreen

Click here to see the complete forum thread (you'll need to be registered user to see photos and join in discussion.)

Tuesday, June 7, 2011

The top attaches to the bottom...


Transporting a 2x1x1m table is an epic task. Not only is the weight a hassle, moving it through downs and around corners becomes near impossible. To make this easier the table is design to break down into pieces. First the legs are held together with the keyed tennons (easily tapped into place) and then screwed/bolted up into the tabletop.

 

The first step in the process is the supports beneath the table. Four 20mm supports stretch under the table and support the thinner (20mm) fiddleback mid section to the thicker 40mm edge pieces. Slotted holes allow for horizontal wood movement while simple brass screw stay in position. Because these sections won't normally need to be removed a screw works well.

Connecting the legs to the support is a different story. These need to be able to tightened and taken apart multiple times over the lifetime of the project. Threading the wood or inset nuts are ok, but I find they wear and fail. 



For this project I'm using 3/16" brass nuts and bolts. I used the leg to mark where to drill. Then counterbored with a forsner bit. With the support removed from the table I could tighten the bolt while holding the nut. Then I filled the counterbore with... epoxy. Leave to set. (Not forgetting to remove the bolt.) A quick sand and oil. And we're done.

 

Sunday, June 5, 2011

Refining the Center Stretcher

Construction of the Anniversary Shaker Table is in the home stretch. Today with the stretcher held securely to the bench I could finish some of the details. A nicholson fine rasp, a cheap riffler and some sand paper made quick work of rounding the edges and fitting the joint.




Holding the stretcher to the legs are keyed through mortise and tennon joints. I made the ebony keys quickly with a chisel and saw. Although a quick and fun way to build... the lack of planing caused one small hassle. A combination of a slight difference in the angle of the key and mortise and leaving the short grain too short caused a small blow out at both ends. The solution... it's now a design feature...

Wednesday, June 1, 2011

Oiling the Benches

Progress may be slow, but progress is progress. One bench is finished and in the house. The other is finished and airing in the shed. Yesterday I put the last coat of oil on it. Using 0000 steel wool I rubbed in a third coat of Organoil wiping the excess with paper towel. After a month or so I'll come back an add a very thin layer of wax. Now onto the legs for the table...



Saturday, May 21, 2011

Woodworking on Holidays: Queensland Museum

Next door to the Queensland Art Gallery is the Queensland Museum. The Museum had a very extensive collection of natural history (including Dinosaur fossils discovered in Queensland) and human history (including household items from before Christ). It also had a number of wooden items.



Friday, May 20, 2011

Woodworking on Holidays: Queensland Art Gallary

Just a few photos from our recent trip to the Queensland Art Gallery. On display was a variety of wooden pieces representing several eras of Australian history (pictured below) as well as some historical international pieces. The Gallery itself was easy to access and quite pleasant to stroll around.  











Saturday, May 14, 2011

Experimental Filling...

The first thirty minutes of shop time I've had in 6 weeks was spent reviewing the pews. It gave me an opportunity to see the results of various filling experiments I tried on the project. (Of course it's recommended do technique 'experiments' on scraps prior to the actual project, but this time it's on the project.)



The first 'filling' job was the plugs to cover the screws. Made with the Veritas Snug Plug cutters from Indian Ebony these proved to be highly successful. (But ebony is not cheap). The plugs simply tap into to place and hold with glue. To finish simply flush trim and sand.

 

The first Epoxy experiment was done using the west system microfiber system. The microfiber in fine powder forms acts to thicken the glue and allow better filling properties. However, this also tinges the filler white... not such a good look.


Next up with have microfiber with fine saw dust. Allow I've had success with this technique in the past this time it made the filler appear heterogenous (ie. tinged white with flecks of reddy brown). Better but not there yet.


My final option was black oxide. This carbon like powder is designed to colour concrete and is dirt cheap. Used with or without microfiber it made a solid homogeous filling agent. Perfect... well if your wanted black any way.

Defects that were exposed to the element while the tree was standing often have a black edge. I presume this is related to oxidation within the wood. Filling these gaps with black filler is effective. 

For other colours, such as to match the reddy brown, I would try even finer saw dust (such as that out of the sander) or turn to dyes and stains to turn that white tinge what ever tinge you want. 

Epoxy has a significant advantage over water based fillers such as 'putty' - strength. Epoxy can seep into the defect, completely fill it, then set harder than wood, holding the defect together. This strength is essential to fill large defects and stablise burls.

Thursday, May 5, 2011

Woodworking on Holidays: HNT Gordon Smoother

A smoothing plane is an incredibly useful tool for both hand tool and power tool enthusiasts. Presently I lack a dedicated smoothing plane (instead using a no 5, or abrasives.) 

After much inward deliberation and hands on comparison at the Sturt Open Day I decided the HNT Gordon a55 was the plane for me. (The other main option was the LN 4 1/2, however, the handle configuration was crowded and less comfortable and the cost greater.)

Unfortunately, the day I was passing HNT Gordon the shop was shut for Easter... so I'll wait for the next wood show...   



Hmmm. That wasn't the best of stories. Oh well... always happy to plug a quality Australian producer. 

Woodworking on Holidays: A tree house of note...

A four week break over the Easter period has enabled us to make a 2500km road trip around New South Wales and into Southern Queensland. Certainly more time was dedicated to building sand castles than woodworking but there were a few woody things of note.

The first wood object of note is this tree house found at the Macadamia Castle. A truly impressive multi-story tree house with multiple entry points and a upper tower fort. Although the tree seemed now deceased I was impressed but the amount of tree growth engulfing the added wooden structure. 




Friday, April 1, 2011

Phew those pews were long overdue...

Work, sickness, and family priorities have led to very little in the way of woodworking these past four or five weeks. Today however I had a break through in assembling the pews. 


The 5" makita ROS sander got a mighty work out. Prior to assembly all pieces went step by step through 120, 180, 240, shellac sealer, 240, and 320grit. It reads quickly, but it took several hours to get through all the pieces.


Repetitive drilling was made easier with a memory stick made from scrap pine. A drill press allowed me to form 90 degree holes at set points in the scrap. The scrap could then be moved along the board and used to guide a hand drill. A quick pilot hole with a twist bit followed by a counterbore with a forsnter bit.


After gluing and screwing the holes were filled with plugs. The plugs were cut using the vertias snug plug system (very nice), glued, tapped, and then flush cut.


There's still work to go; more sanding, and then the oiling begins.

Like at Facebook

Redbubble